0
   

Rainsoft gear stripped

 
 
Reply Tue 24 May, 2011 11:12 am
Hello,
I have a old (1998ish) Rainsoft AM24 conditioner that hasn't been working for the past couple months. I checked the transformer... 26 volts on it, all the relays appear to be fine, but it wasn't making any noise and wouldn't move at all. I took everything apart and checked the motor while it was detached from the "transmission" box. It runs fine. I took the gear box apart and found that the gears were jammed. There are five gears inside the box: 2 metal gears and 3 smaller plastic gears. The drive order appears to be motor shaft to fine toothed plastic gear to a courser toothed plastic gear to a second courser toothed gear (this one is stripped on the bottom-11 tooth side) to a metal gear to a larger metal gear that the cam shaft is on. I called RS and took forever trying to explain to them the gear that I needed. When they finally understood what i needed they said that they couldn't get the part. They can only replace the entire $160 motor assembly. Does anyone no where I can find this one plastic gear?
  • Topic Stats
  • Top Replies
  • Link to this Topic
Type: Question • Score: 0 • Views: 4,473 • Replies: 10
No top replies

 
H2O MAN
 
  1  
Reply Wed 25 May, 2011 04:29 pm
@QuickPuppy,
Are you talking about the clock motor?

It has two white wires coming off one end
and a brass gear sticking out of the other end.
QuickPuppy
 
  1  
Reply Wed 25 May, 2011 06:35 pm
@H2O MAN,
I don't think so... it's the motor that runs the shaft (that has the brass pin holding it on) that the two white cams are on that raise/lower the piston and brine valves.
QuickPuppy
 
  1  
Reply Wed 25 May, 2011 08:02 pm
@QuickPuppy,
It does have two white wires that converge into one white wire that attaches to one post on the motor. There is also a blue wire attached to the other motor post. This whole assembly is behind the box houses the timer and behind the white cams. It sits over the piston/valve on top of the media tank. If I can figure out how to post a pic I will shortly.
0 Replies
 
QuickPuppy
 
  1  
Reply Wed 25 May, 2011 08:07 pm
@H2O MAN,
http://www.flickr.com/photos/63334960@N06/sets/72157626682602001/

Here's the piece all taken apart.
0 Replies
 
QuickPuppy
 
  1  
Reply Wed 25 May, 2011 08:26 pm
@H2O MAN,
http://www.flickr.com/photos/63334960@N06/sets/72157626682722807/ Here is the assembled part.
H2O MAN
 
  1  
Reply Thu 26 May, 2011 11:03 am
@QuickPuppy,
That's the valve motor that turns the cams...

I have these in stock - pm me with your email and shipping address
and I will quote a price. You are under no obligation to buy from me.
Lewandowski911
 
  1  
Reply Thu 19 Apr, 2012 08:37 pm
@H2O MAN,
I need the same thing for my Rainsoft my plastic gear stripped out please email me with a price thanks [email protected]
0 Replies
 
Lewandowski911
 
  1  
Reply Thu 19 Apr, 2012 09:38 pm
@H2O MAN,
My gears stripped out because my valve got stuck H2o do you have valve rebuild kits for the older model am744t and valve motor gears or motor it self ? Please let me know thanks
0 Replies
 
stevek1988
 
  1  
Reply Tue 2 Apr, 2013 09:18 am
@H2O MAN,
Hello H20 man, Can i get a price for the rainsoft drive motor (unit intstalled 1999)
Thanks
Steve Kaminski
[email protected]
0 Replies
 
jc21773924
 
  1  
Reply Tue 23 Apr, 2013 09:56 am
@H2O MAN,
This exactly what I need, do you repair the valve or just send the parts?, please let me know, my e-mail address is [email protected]
0 Replies
 
 

Related Topics

 
  1. Forums
  2. » Rainsoft gear stripped
Copyright © 2024 MadLab, LLC :: Terms of Service :: Privacy Policy :: Page generated in 0.08 seconds on 11/23/2024 at 07:23:26